Standby power is the electricity that devices use while they are plugged in but switched off or idle. Each device usually draws only a few watts, but because that draw runs 24 hours a day, every day, it adds up to a steady, measurable slice of your electric bill. You can find out exactly how much it costs in your own home with a plug-in watt meter or your utility's hourly usage data, and then cut the biggest offenders without giving up anything you use.
What standby power is
Many electronics never fully turn off. A television waits for the remote, a cable or satellite box keeps its guide updated, a game console stays ready to download updates, and a microwave keeps its clock lit. Phone chargers left in the wall, smart speakers, wireless routers, printers and desktop computers in sleep mode all draw a small amount of power around the clock.
This is sometimes called phantom load, vampire power or idle load. Some of it is useful, such as a router you rely on overnight or a security camera. Some of it is pure waste, such as a game console set to an instant-on mode in a spare room that nobody uses during the week.
How to work out what a device costs
The math is simple and works for any device:
- Find the standby draw in watts, ideally by measuring it.
- Multiply watts by 24 hours, then by 365 days.
- Divide by 1,000 to get kilowatt-hours (kWh) per year.
- Multiply by the price per kWh shown on your electric bill.
For example, a device that draws 5 watts all the time uses 5 × 24 × 365 ÷ 1,000 = 43.8 kWh a year. For every 10 cents you pay per kWh, that is about $4.38 a year. A 20-watt load running constantly uses 175.2 kWh a year, or about $17.52 for every 10 cents per kWh. Use the total price per kWh from your own bill, including fuel and other per-kWh charges, for an accurate figure.
One device rarely matters much. A house full of them, running every hour of every day, can matter more than most people expect.
Measuring standby power in your home
There are two practical ways to measure it, and they work well together.
Plug-in watt meter. These inexpensive meters plug into an outlet, and you plug the device into the meter. Check the reading with the device off, in standby and in use. Measure a power strip with everything plugged in to see the combined load of an entertainment center or home office.
Your utility's usage data. Most homes in the Panhandle have smart meters. If your utility shows hourly usage in its online account or app, look at the hours between about 2 a.m. and 5 a.m. on a mild night when the heating and air conditioning are not running much. That overnight floor is your home's baseline load: the refrigerator, freezer, water heater cycles and every always-on device combined. FPL customers can view usage in their online account; if you are with CHELCO, Gulf Coast Electric, West Florida Electric, Escambia River Electric or Talquin, check whether your co-op's member portal shows hourly data.
If you are not sure which utility serves your address, your bill or meter will tell you. Rates and the detail available online differ from one utility to the next.
The usual standby offenders
These are the devices worth measuring first:
- Cable and satellite boxes with DVRs. Many draw nearly as much power when "off" as when on, because they keep recording and updating.
- Game consoles. Instant-on or rest modes keep them partly awake so they can download updates.
- Older televisions and sound bars. Newer models are generally more efficient in standby, but older sets and some audio equipment can draw more.
- Desktop computers, monitors and printers. Sleep settings vary widely, and some never really sleep.
- Second refrigerators and chest freezers. These are not standby loads, but an old fridge in a hot garage is often the biggest always-on load in a Florida home.
- Well pumps, irrigation controllers, pool equipment and hot tubs. Timers and controls left on the wrong settings can run equipment far more than needed.
Chargers with nothing attached, digital clocks and small smart plugs usually draw very little. They are not worth worrying about unless you find many of them.
Easy ways to cut standby power
You do not need to unplug everything every night. Focus on the loads that measure highest and the ones you do not need:
- Switch off instant-on modes on game consoles and televisions in the settings menu.
- Use a switched power strip for an entertainment center or home office, so one switch turns everything off. Advanced power strips can shut off accessories automatically when the main device turns off.
- Turn on sleep settings for computers, monitors and printers.
- Unplug or remove equipment you no longer use, such as an old DVD player, a spare cable box or a second refrigerator holding a few drinks.
- Check timers and controllers on pool pumps, irrigation systems and water heaters, especially after a power outage, which can reset some timers.
- Leave on what you need. Routers, modems, security systems, medical equipment and refrigerators should stay powered.
Solar Cost Calculator – Florida Panhandle Only
* Estimate based on $3.25 per watt for solar installation.
* For Tesla Powerwall 3 Batteries, $15,000 for the first battery, $12,000 for each additional battery.
* Other variations and types of Batteries are available.
Why baseline load matters for solar and batteries
Your overnight baseline load is useful information if you have solar or are considering it. Solar panels produce nothing at night, so every watt of always-on load at night comes from the grid or from a home battery.
With a battery, baseline load has an even more direct effect. During a hurricane outage, a home battery runs the always-on loads around the clock. A lower baseline means stored energy lasts longer between sunny days, leaving more for the refrigerator, lights, fans and other essentials. Measuring and trimming standby power is one of the cheapest ways to stretch backup power.
For new solar systems, a lower and well-understood baseline helps size the system accurately to your real usage instead of to wasted power. MSM Solar offers free site surveys and written quotes; typical pricing is about $3.25 per watt installed, and about $15,000 for a first Tesla Powerwall 3. See our new installations page for how the process works.
The 30% federal residential solar tax credit and the home battery credit ended for systems installed after December 31, 2025, so savings now come from the bill itself. That makes cutting wasted usage even more worthwhile before you size a system.
When a high baseline points to a bigger problem
If your overnight usage looks high even after you have dealt with the obvious devices, something larger may be running. Common causes include a water heater element that cycles constantly because of a leak or failing thermostat, a well pump that short-cycles, a refrigerator or freezer with a failing seal or dirty coils, a dehumidifier running nonstop, or a pool pump timer that was never reset.
Turning off breakers one at a time while watching the meter or your hourly data can narrow down the circuit. If you are not comfortable working at the electrical panel, call a licensed electrician.
If you already have solar and suspect your system is not offsetting as much as it used to, the problem may be on the production side instead. MSM Solar handles solar system service calls for any brand and age of system, including systems whose original installer has closed.
Frequently asked questions
Does unplugging chargers save money?
A phone charger with nothing attached usually draws very little, so the savings are small. Measure larger devices such as DVR boxes and game consoles first.
Is it safe to put my TV and cable box on a switched power strip?
Generally yes, but some cable and satellite boxes take a while to restart and may miss scheduled recordings while off. Leave those plugged in if recordings matter to you.
What is a normal overnight baseline for a home?
It varies widely with the number of refrigerators, freezers, pumps and electronics. The best benchmark is your own home before and after you make changes.
Will cutting standby power reduce the size of a solar system I need?
It can, slightly, because a solar system is sized to your yearly usage. The bigger benefit is with a home battery, where a lower baseline makes stored energy last longer during an outage.
Conclusion
MSM Solar works with homeowners in Fort Braden, Fountain, Freeport, Graceville and Greensboro, and in every town between Pensacola and Apalachicola.
Standby power is a small, constant draw that quietly adds to every bill. Measure the devices you suspect, check your overnight baseline in your utility's usage data, and switch off or remove the loads you do not need. If you are in Crestview, Milton, Panama City or elsewhere in the Panhandle and want to see how a leaner baseline fits with solar or a home battery, call MSM Solar at (850) 737-5197. A real person calls back within 2 business days.