Skip to main content

Solar lowers the part of your bill that comes from electricity you pull from the grid, but it does not remove fixed charges, it produces less on short winter days and cloudy stretches, and it cannot cover household use that has grown since the system was sized. If your bill is much higher than you expected, the usual causes are a system that is not producing, a meter or net metering setup that is not finished, or usage that has outgrown the system. This guide walks through each one so you can find the cause yourself before you call anyone.

What solar can and cannot take off your bill

A grid-tied solar system reduces the kilowatt-hours (kWh) you buy from your utility. Every kWh your panels make is either used in the house right away or sent out to the grid and credited. What solar does not touch are the parts of the bill that are not based on kWh.

  • Fixed customer charge. Nearly every utility in the Panhandle bills a fixed monthly charge just for being connected. You pay it whether you use 50 kWh or 2,000 kWh.
  • Minimum bill rules. FPL bills include a minimum bill provision, so even a month where solar covers all of your use will not drop to zero. The amount is listed in your utility's rate schedule.
  • Taxes and franchise fees. These are calculated on the charges that remain and never fully disappear.

So the realistic goal for most homes is a much smaller bill, not a zero bill. If you are paying close to what you paid before solar, though, something else is going on.

First check: is the system actually producing?

The most common reason for a surprise bill is a system that stopped working and nobody noticed. Grid-tied inverters shut off when the grid goes down and are supposed to restart on their own, but a tripped breaker, a fault code or a lost internet connection can leave them off or leave you blind to what they are doing.

  • Open your monitoring app and look at daily production for the last few weeks. A run of zero days, or a sudden drop, points to a hardware or connection problem.
  • Look at the inverter itself. A green or steady status light usually means it is running; red, orange or a flashing fault light usually means it is not.
  • Check the solar breaker in your main panel and the outdoor disconnect. A breaker can trip during a storm or a power surge.
  • If the app shows no data at all, the problem may only be the Wi-Fi link. Compare with the received number on your utility bill before assuming the panels are off.

If you find a fault you cannot clear, our solar system service calls cover diagnosis and repair on any brand and age of system, including orphaned systems whose original installer has closed.

Make sure net metering is fully set up

A new system is not supposed to run until the utility gives permission to operate and installs or reprograms a meter that records power in both directions. If the system was turned on early, or the meter swap took longer than expected, your first bills may not show any export credit at all.

On a properly set up bill you should see two meter readings: energy delivered to you from the grid and energy received from you by the grid. If your bill only shows one number, call your utility and ask whether your account is on its net metering rate.

FPL, which now serves the former Gulf Power territory, credits net-metered exports at the retail rate. Under Florida's net metering rule for investor-owned utilities, extra credits roll forward month to month, and any left over at the end of the annual period are paid out at a much lower rate. The local co-ops and city utilities, including CHELCO, Gulf Coast Electric, West Florida Electric, Escambia River Electric and Talquin, set their own rules. Some credit exports differently from retail power, which changes how much solar is worth on those bills. Read your own co-op's net metering policy rather than assuming it matches FPL.

Seasonal swings in the Florida Panhandle

Solar production and household use move in different directions through the year. In December and January the days are short and the sun sits low, so a system may make noticeably less than it does in spring. At the same time, cold nights can push a heat pump into auxiliary electric heat, which uses far more power than normal heating.

Summer brings long days but also heavy air conditioning load and afternoon thunderstorms that cut production for a few hours at a time. A single month is a poor test of whether solar is working. Compare twelve months of bills with the twelve months before installation, and compare each month with the same month a year earlier.

Your household use may have grown

A solar system is sized from the usage history you had when it was designed. If that usage has gone up, the same system covers a smaller share of the bill. Common reasons in Panhandle homes include:

  • An electric vehicle charging at home
  • A new pool, pool heater or hot tub
  • A room addition, workshop or second refrigerator
  • More people living in the house, or someone working from home
  • An aging air conditioner that runs longer to keep up

Look at the delivered kWh on your bill and compare it with the same month last year. If delivered energy has climbed while production looks normal, the cause is the house, not the panels. If the extra use is permanent, adding panels to an existing system is often simpler than starting over.

Shade, dirt and storm damage

Production can fall slowly without any error light. Trees grow a few feet every year, and a pine that cleared the array at installation can shade part of it a few years later. Heavy pollen, bird droppings and dust can build up during dry spells. After a hurricane or strong storm, a cracked panel, loose wiring or a shifted rail can take part of the array offline while the rest keeps running.

Panels also lose a small amount of output each year as they age. That loss is gradual and should not explain a sudden jump in your bill. A sharp change from one year to the next almost always has a more specific cause.

Rate changes and billing period differences

Utilities adjust base rates, fuel charges and other line items from time to time, so the same kWh can cost more this year than last. Billing periods also vary from about 28 to 33 days, and an estimated meter read can shift usage from one bill to the next. When you compare bills, compare kWh delivered and received, not just the dollar total.

How to work out your real household use

Your meter only sees power crossing it. Solar that your house uses directly never shows up on the bill, which is why the bill alone can be misleading. You can estimate your actual use for a billing period with three numbers:

  1. Delivered kWh from your utility bill
  2. Total production for the same dates from your monitoring app
  3. Received kWh from your utility bill

Household use equals delivered plus production minus received. If that total is far higher than your usage before solar, the house is using more. If production is far lower than the same month last year, the system needs attention.

Solar Cost Calculator – Florida Panhandle Only

* Estimate based on $3.25 per watt for solar installation.
* For Tesla Powerwall 3 Batteries, $15,000 for the first battery, $12,000 for each additional battery.
* Other variations and types of Batteries are available.





When to call for an inspection

Call a solar contractor if production is zero or well below the same month last year, the inverter shows a fault you cannot clear, part of the array looks damaged after a storm, or you cannot get monitoring data and the bill shows little or no export. MSM Solar is based in Crestview and holds Florida Certified Solar Contractor License CVC57236. We quote service-call pricing up front, and a real person calls back within two business days. Homeowners in Crestview, Niceville, Fort Walton Beach and the rest of our service areas can reach us at (850) 737-5197.

Frequently asked questions

Should my electric bill be zero with solar?

Rarely. Fixed customer charges, minimum bill rules, taxes and fees remain even when solar covers all of your energy use. A small bill is the normal result.

Why was my first bill after installation so high?

The system may not have been turned on until permission to operate was granted, the meter may not have been changed yet, or the bill may cover days before the system started. Check that your bill shows both delivered and received kWh.

Do co-ops credit solar exports the same way FPL does?

Not necessarily. CHELCO, Gulf Coast Electric, West Florida Electric, Escambia River Electric and Talquin each set their own net metering rules. Ask your co-op how exported energy is credited on your account.

Will a battery lower my bill?

Under FPL's retail-rate net metering, a battery mostly adds backup power rather than bill savings. On utility plans that credit exports below retail, storing midday solar for evening use can help. Your utility's rules decide which applies.

Conclusion

MSM Solar works with homeowners in Ponce de Leon, Quincy, Rosemary Beach, Seaside, St. George Island, Tallahassee and Wewahitchka, and in every town between Pensacola and Apalachicola.

A high bill after going solar usually comes down to one of four things: the system is not producing, net metering is not set up, the season is working against you, or the house now uses more power. Start with your monitoring app and the delivered and received numbers on your bill, compare against the same month last year, and the cause is usually clear. If the numbers point to the equipment, have it inspected before months of lost production add up.