Skip to main content

Every solar panel loses a small amount of output each year. For most modern panels the loss is slow and steady, and many manufacturers' performance warranties promise roughly 80 to 90 percent of rated output after 25 years. That kind of gradual aging should not cause a sudden drop in production. If your system makes noticeably less than it did a year ago, something more specific, like shade, a failed component or storm damage, is usually to blame.

What solar panel degradation means

Degradation is the gradual loss of a panel's ability to turn sunlight into electricity. It happens because the materials inside the panel slowly change with years of sunlight, heat and moisture. The cells, the coating on the glass, the solder joints and the protective layers all age a little.

Degradation is different from a failure. A degraded panel still works, just slightly less well than when it was new. A failed panel, a cracked cell or a burned connection can cut output sharply and often needs repair or replacement.

What panel warranties say about output loss

Most panels come with two separate warranties, and it helps to know which is which:

  • Product warranty. Covers defects in materials and workmanship, such as a delaminating back sheet or a failed junction box.
  • Performance warranty. Promises the panel will still produce a stated percentage of its rated power after a set number of years, often 25.

The performance warranty usually allows a larger loss in the first year, when panels go through a short settling period after first exposure to sunlight, and a smaller allowance each year after that. The exact figures differ by brand and model, so find the datasheet or warranty document for your panels. The model number is printed on a label on the back of each panel and is usually listed in your installation paperwork.

What speeds up degradation in the Florida Panhandle

Panels age faster in some conditions than others, and several of them are common here:

  • Heat. Long, hot summers put the materials under steady thermal stress, and daily heating and cooling expands and contracts solder joints.
  • Humidity. Moisture that works its way into a panel over time can corrode internal connections, especially in lower-quality panels.
  • Salt air. Homes near the coast in places like Navarre, Destin and Perdido Key see more corrosion on frames, racking and connectors than homes inland.
  • Storm stress. High winds and flying debris can cause tiny cracks in cells that are invisible from the ground but reduce output over time.
  • Installation quality. Panels that were walked on, clamped incorrectly or wired poorly can develop problems earlier than they should.

Normal aging or a fixable problem?

The key difference is speed. Normal degradation is so gradual that you would barely notice it from one year to the next. If production falls noticeably over one season, look for another cause first:

  • Shade. Trees grow, and a neighbor may have built something new. Even partial shade on one panel can pull down a whole string on some systems.
  • Inverter faults. An inverter that is derating, tripping or partly offline can look like weak panels.
  • A string or panel offline. A loose connector, a blown fuse or a failed microinverter can take part of the array out of service while the rest keeps running.
  • Dirt and debris. Pollen, leaves and bird droppings reduce output until they are cleared.
  • Visible panel damage. Cracked glass, browning, bubbling or burn marks call for an inspection, not patience.
  • Weather. A cloudier than usual year will produce less, and that is not a sign of aging.

How to track your system's output

You do not need special tools to keep an eye on degradation. A simple yearly record is enough:

  1. Write down total production for each month from your monitoring app.
  2. Compare each month with the same month in earlier years, not with the month before.
  3. Look at the annual total once a year. A small decline over several years is normal; a large drop in a single year is not.
  4. If you have microinverters or panel-level monitoring, compare panels against each other. One panel producing well below its neighbors points to a problem with that panel or its shading.

If your monitoring has stopped reporting, the received kWh on your utility bill gives a rough second check on how much the system is exporting.

Solar Cost Calculator – Florida Panhandle Only

* Estimate based on $3.25 per watt for solar installation.
* For Tesla Powerwall 3 Batteries, $15,000 for the first battery, $12,000 for each additional battery.
* Other variations and types of Batteries are available.





What can and cannot be fixed

Normal degradation cannot be reversed, and cleaning will not undo it. Most other causes of lost production can be fixed:

  • Damaged or failed panels can be replaced, though matching an older model may take some searching.
  • A failing inverter can be repaired or replaced, and an older string inverter often wears out before the panels do.
  • Loose or corroded connectors and wiring can be repaired.
  • Shading can sometimes be reduced by trimming trees.

If your household now needs more power than an aging system can supply, adding panels to an existing system can make up the difference without replacing panels that still work.

Warranty claims on older and orphaned systems

A performance warranty claim usually requires proof that output has fallen below the guaranteed level, which often means testing by a qualified contractor and your original paperwork: the panel model and serial numbers, the installation date and the invoice. Keep these together in one place.

If the company that installed your system has closed, you can still have it serviced. MSM Solar, based in Crestview with Florida Certified Solar Contractor License CVC57236, works on any brand and age of system, including orphaned systems. We provide solar system service calls across our service areas, quote service-call pricing up front, and a real person calls back within two business days. Call (850) 737-5197.

Frequently asked questions

Do solar panels stop working after 25 years?

No. The 25-year figure is usually the length of the performance warranty, not the life of the panel. Panels typically keep producing after that, just at a somewhat lower level than when new.

Does cleaning fix degradation?

No. Cleaning removes dirt that blocks sunlight, which can restore lost output from buildup, but it does not change the slow aging inside the panel.

Should I replace old panels just because they have degraded?

Usually not. Panels that are working normally for their age are still producing useful power. Replacement makes more sense when panels are damaged, failing or no longer covered and causing repeated problems.

How do I know my panel model and warranty terms?

Check the label on the back of a panel or your installation paperwork for the model number, then look up that model's datasheet and warranty document from the manufacturer.

Conclusion

MSM Solar works with homeowners in Alford, Altha, Apalachicola, Blountstown, Bonifay, Cantonment and Chipley, and in every town between Pensacola and Apalachicola.

Solar panels lose a little output every year, and that slow decline is expected and built into how systems are sized and warrantied. What is not normal is a sudden drop. Track your production year over year, compare the same months, and if one season or one year looks much worse than the last, have the system checked. Shade, an inverter problem or storm damage is far more likely than aging, and those causes can usually be fixed.